暂无标题

doi:10.16579/j.issn.1001.9669.2021.01.035

您当前的位置：

首页 >

文章列表页 >

暂无标题

更新时间：2022-09-22

- 暂无标题
- Journal of Mechanical Strength Issue 1, Pages: 239-243(2021)
- 作者机构：
  
  南京航空航天大学机电学院
- 作者简介：
- 基金信息：
- DOI：10.16579/j.issn.1001.9669.2021.01.035
  CLC：
扫描看全文
[J]. Journal of Mechanical Strength (1):239-243(2021)
DOI：

[J]. Journal of Mechanical Strength (1):239-243(2021) DOI： 10.16579/j.issn.1001.9669.2021.01.035.

摘要

新型机加工弹簧静态拉压时螺旋槽端部应力集中现象十分严重,对弹簧的强度和疲劳寿命有很大的影响。通过Ansys软件分析弹簧基本参数对应力集中的影响,确定机加工弹簧存在应力集中的理论判据;探究切向应力释放孔对压缩变形量和应力集中系数的影响;基于强度理论和曲梁弯曲理论推导了无应力集中下的最大等效应力计算公式。研究表明:中径在15 mm～35 mm之间的机加工弹簧,当螺旋槽宽度与螺距之比小于0.5时存在应力集中现象;螺旋槽端部开切向应力释放孔,控制其孔径接近对应矩形截面高度时可将应力集中基本消除;所推导公式计算的内圈等效应力值与仿真值误差不超过3%,为该弹簧后续的工程设计及应用提供了重要参考。

Abstract

The stress concentration at the end of spiral groove is very serious during the static tension and compression of the new machined spring,which has a great influence on the strength and fatigue life of the spring.The influence of spring basic parameters on the stress concentration coefficient was analyzed by ANSYS software,and the theoretical criterion for the existence of stress concentration in machined springs is determined.The effects of tangential stress release hole on compression deformation and stress concentration coefficient were investigated; Based on the strength theory and bending theory of curved beam,the formula of maximum equivalent stress without stress concentration was deduced.The results show that when the ratio of the width of the spiral groove to the pitch is less than 0.5,stress concentration occurs in machined springs with the middle diameter between 15 mm ～ 35 mm.The stress concentration can be basically eliminated by cutting stress release hole at the end of spiral groove and controlling its size to be close to the height of rectangular section.The error between the equivalent stress value of the inner ring and the simulation value is less than 3%.It provides an important reference for the subsequent engineering design and application of the new spring.

关键词

机加工弹簧应力集中应力释放孔等效应力有限元分析

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

THE SUBMODELING METHOD ANALYSIS ON POST-BUCKLING WEAR PREDICTION OF COMPRESSION COILED TUBING IN WELLBORE (MT)

STUDYONDEFORMATIONFORMANDENERGYABSORPTIONCHARACTERISTICS OF METAL THIN-WALLED SANDWICH STRUCTURE (MT)

EFFECT OF FDM PROCESS PARAMETERS ON TENSILE STRENGTH BASED ON FLUID THERMAL ANALYSIS (MT)

DESIGN AND SIMULATION VERIFICATION OF METRO ENERGY ABSORBED STRUCTURE BASED ON ASME RT-2 STANDARD (MT)

EXPERIMENTAL STUDY ON FRETTING FATIGUE OF 2024 ALUMINUM ALLOY UNDER ALTERNATING NORMAL LOAD (MT)

Related Author

No data

Related Institution

Downhole Service Branch of Daqing Oilfield Co., Ltd.

School of Mechanical Science and Engineering, Northeast Petroleum University

College of Aerospace and Architectural Engineering, Harbin Engineering University

College of Mechanical Engineering, University of Shanghai for Science and Technology

Carbody Platform Department,CRRC Changchun

⁰

暂无标题

DOI：10.16579/j.issn.1001.9669.2021.01.035

摘要

Abstract

关键词

Keywords

references