1.西安工程大学 机电工程学院,西安 710600
2.西安热工研究院有限公司,西安 710054
赵嘉欣,女,1997年生,山西大同人,硕士研究生;主要研究方向为滚动轴承基础研究及数值模拟;E-mail:zhaojiaxin0716@163.com。
收稿:2025-03-21,
修回:2025-05-08,
纸质出版:2026-10-15
移动端阅览
赵嘉欣,邢宇,贾逸飞,等. 基于裂纹表面特征的变桨轴承裂纹扩展路径研究[J]. 机械强度,2026,48(10):74-85.
Zhao Jiaxin,Xing Yu,Jia Yifei,et al. Study on crack propagation path of pitch bearings based on crack surface characteristics[J]. Journal of Mechanical Strength,2026,48(10):74-85.
赵嘉欣,邢宇,贾逸飞,等. 基于裂纹表面特征的变桨轴承裂纹扩展路径研究[J]. 机械强度,2026,48(10):74-85. DOI: 10.16579/j.issn.1001.9669.2026.10.009.
Zhao Jiaxin,Xing Yu,Jia Yifei,et al. Study on crack propagation path of pitch bearings based on crack surface characteristics[J]. Journal of Mechanical Strength,2026,48(10):74-85. DOI: 10.16579/j.issn.1001.9669.2026.10.009.
目的
2
针对变桨轴承裂纹扩展路径和尖端偏转角预测这一问题,在保证计算精度的前提下,提出一种计算效率较高的基于等效有限元模型和多元多项式回归模型的预测方法。
方法
2
首先,分析裂纹长深比、裂纹径向角、裂纹位置角、螺栓预紧力等不同参数对裂纹前缘应力强度因子的影响规律,构建描述变桨轴承工况条件和几何特征的有限元模型;其次,基于断裂力学理论、Paris公式和最大切应力准则,分析裂纹表面特征对裂纹尖端偏转角的作用机制;最后,利用多元多项式回归模型,建立多因素影响下的裂纹尖端偏转角预测模型。
结果
2
结果表明,裂纹萌生区域主要位于外圈螺栓孔的径向区域,裂纹以张开型为主;裂纹初始径向角对裂纹尖端偏转角的影响最大,裂纹扩展速率随裂纹长深比的增加而增加;利用多元多项式回归模型建立的裂纹尖端偏转角预测模型的预测效果较好。研究成果可有效应用于风电场运维人员对变桨轴承裂纹扩展路径的预测,为变桨轴承的裂纹评估与寿命预测提供参考。
Objective
2
Aiming at the problem of predicting the crack propagation path and crack tip deflection angle of pitch bearings
on the premise of ensuring calculation accuracy
a prediction method based on the equivalent finite element model and multivariate polynomial regression model was proposed
which has a high calculation efficiency.
Methods
2
Firstly
the influence laws of different parameters such as crack aspect ratio
crack radial angle
crack position angle
and bolt preload on the stress intensity factor of the crack front were analyzed
and a finite element model describing the operating conditions and geometric characteristics of the pitch bearing was established. Secondly
based on fracture mechanics theory
the Paris formula
and the maximum shear stress criterion
the mechanism of the effect of crack surface characteristics on the crack tip deflection angle was analyzed. Finally
a prediction model for the crack tip deflection angle under the influence of multiple factors was established using a multivariate polynomial regression model.
Results
2
The results show that the crack initiation region is mainly located in the radial area of the bolt holes on the outer ring
with the cracks being dominated by the opening mode. The initial radial angle of the crack has the most significant influence on the crack tip deflection angle
and the crack propagation rate increases with the increase of the crack depth-length ratio. The prediction model for the crack tip deflection angle established based on the multivariate polynomial regression model exhibits good prediction performance. The research results can be effectively applied to the prediction of crack propagation paths of pitch bearings by wind farm operation and maintenance personnel
providing a reference for the crack assessment and life prediction of pitch bearings.
Kandukuri S T , Klausen A , Karimi H R , et al . A review of diagnostics and prognostics of low-speed machinery towards wind turbine farm-level health management [J]. Renewable and Sustainable Energy Reviews , 2016 , 53 : 697 - 708 .
He P Y , Hong R J , Wang H , et al . Pitch bearing/raceway fretting:influence of contact angle [J]. Proceedings of the Institution of Mechanical Engineers,Part C:Journal of Mechanical Engineering Science , 2019 , 233 ( 5 ): 1734 - 1749 .
董惠敏 , 姚文龙 , 王德伦 , 等 . 变桨轴承连接螺栓有限元分析及试验验证 [J]. 机械设计 , 2019 , 36 ( 增刊1 ): 21 - 25 .
Dong Huimin , Yao Wenlong , Wang Delun , et al . Finite element analysis and test verification of connection bolts of pitch bearing [J]. Journal of Machine Design , 2019 , 36 ( S1 ): 21 - 25 . (In Chinese)
Smolnicki T , Rusiński E . Superelement-based modeling of load distribution in large-size slewing bearings [J]. Journal of Mechanical Design , 2007 , 129 ( 4 ): 459 - 463 .
廖祥林 . 大型风力发电机组变桨轴承滚道分析与优化 [D]. 重庆 : 重庆大学 , 2018 , 15 - 28 .
Liao Xianglin . Analysis and optimization of pitch bearing raceways for large wind turbines [D]. Chongqing : Chongqing University , 2018 : 15 - 28 . (In Chinese)
李朋飞 , 王靖岳 , 郑珺文 , 等 . 基于等效替代下滚动轴承滚子接触载荷算法研究 [J]. 机械传动 , 2023 , 47 ( 6 ): 65 - 70 .
Li Pengfei , Wang Jingyue , Zheng Junwen , et al . Research on the roller contact load algorithm of rolling bearings based on the equivalent substitution [J]. Journal of Mechanical Transmission , 2023 , 47 ( 6 ): 65 - 70 . (In Chinese)
Bomidi J A R , Sadeghi F . Three-dimensional finite element elastic-plastic model for subsurface initiated spalling in rolling contacts [J]. Journal of Tribology , 2014 , 136 ( 1 ): 011402 .
张宇 , 史小玉 , 田为松 . 不同服役工况条件下圆锥滚子轴承磨损研究 [J]. 机械强度 , 2025 , 47 ( 1 ): 123 - 133 .
Zhang Yu , Shi Xiaoyu , Tian Weisong . Study on wear of tapered roller bearing under different service conditions [J]. Journal of Mechanical Strength , 2025 , 47 ( 1 ): 123 - 133 . (In Chinese)
Huang Z P , Du J , Wang S . Subsurface cracks analysis of pitch bearing based on interaction integral method [C]// Proceedings of the Second IYSF Academic Symposium on Artificial Intelligence and Computer Engineering . Bellingham : SPIE , 2021 : 106 .
张洪伟 , 吉康康 , 曹钢 , 等 . 变桨轴承用42CrMo钢疲劳裂纹扩展试验及螺栓孔裂纹扩展特性研究 [J]. 塑性工程学报 , 2024 , 31 ( 9 ): 197 - 206 .
Zhang Hongwei , Ji Kangkang , Cao Gang , et al . Research on fatigue crack growth test of 42CrMo steel for pitch bearing and crack growth characteristics of bolt hole [J]. Journal of Plasticity Engineering , 2024 , 31 ( 9 ): 197 - 206 . (In Chinese)
余江鸿 , 彭俊 , 邵京伟 , 等 . 考虑残余应力的球轴承外圈滚道裂纹扩展规律的研究 [J/OL]. 轴承 , 2024-11-13 . https://link.cnki.net/urlid/41.1148.TH.20241112.1139.002 https://link.cnki.net/urlid/41.1148.TH.20241112.1139.002 .
Yu Jianghong , Peng Jun , Shao Jingwei , et al . Study on the crack propagation law of the outer raceway of ball bearings considering residual stress [J/OL]. Bearing , 2024-11-13 . https://link.cnki.net/urlid/41.1148.TH.20241112.1139.002 https://link.cnki.net/urlid/41.1148.TH.20241112.1139.002 . (In Chinese)
张珂 , 李青松 , 夏卫华 . 考虑预裂纹的滚动轴承疲劳寿命预测 [J]. 机电工程 , 2022 , 39 ( 8 ): 1031 - 1040 .
Zhang Ke , Li Qingsong , Xia Weihua . Fatigue life prediction of rolling bearings considering pre-cracks [J]. Journal of Mechanical & Electrical Engineering , 2022 , 39 ( 8 ): 1031 - 1040 . (In Chinese)
Harris T A , Kotzalas M N . Rolling bearing analysis [M]. 5th ed . Boca Raton : CRC Press/Taylor & Francis Group , 2007 : 267 - 303 .
0
浏览量
0
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构
京公网安备11010802024621