RESEARCH ON CBN GRINDING WHEEL PERFORMANCE MONITORING METHOD BASED ON SHANNON ENTROPY AND ACOUSTIC EMISSION SIGNAL (MT)

TAN YongMin; SHI Zhan; CHI YuLun; GU JiaJian

doi:10.16579/j.issn.1001.9669.2023.02.010

您当前的位置：

首页 >

文章列表页 >

RESEARCH ON CBN GRINDING WHEEL PERFORMANCE MONITORING METHOD BASED ON SHANNON ENTROPY AND ACOUSTIC EMISSION SIGNAL (MT)

更新时间：2023-06-09

- RESEARCH ON CBN GRINDING WHEEL PERFORMANCE MONITORING METHOD BASED ON SHANNON ENTROPY AND ACOUSTIC EMISSION SIGNAL (MT)
- Journal of Mechanical Strength Issue 2, Pages: 321-330(2023)
- 作者机构：
  
  1. 上海理工大学光电信息与计算机工程学院
- 作者简介：
- 基金信息：
- DOI：10.16579/j.issn.1001.9669.2023.02.010
  CLC：
扫描看全文
TAN YongMin, SHI Zhan, CHI YuLun, et al. RESEARCH ON CBN GRINDING WHEEL PERFORMANCE MONITORING METHOD BASED ON SHANNON ENTROPY AND ACOUSTIC EMISSION SIGNAL (MT). [J]. Journal of Mechanical Strength (2):321-330(2023)
DOI：

TAN YongMin, SHI Zhan, CHI YuLun, et al. RESEARCH ON CBN GRINDING WHEEL PERFORMANCE MONITORING METHOD BASED ON SHANNON ENTROPY AND ACOUSTIC EMISSION SIGNAL (MT). [J]. Journal of Mechanical Strength (2):321-330(2023) DOI： 10.16579/j.issn.1001.9669.2023.02.010.

摘要

为了在磨削加工过程中能够有效判别CBN(Cubic Boron Nitride)砂轮的磨削性能，提出了一种基于Shannon熵理论与声发射信号的CBN砂轮性能监测方法。首先，利用声发射传感器采集CBN砂轮磨削加工过程中的声发射信号，基于最大信息熵对CBN砂轮磨削加工过程中的声发射信号进行概率密度估计，获得磨削加工过程中声发射信号的最大熵概率密度分布。然后，通过分析研究CBN砂轮在修整过后循环磨削以及不同直径剩余磨削时的声发射信号特征，根据交叉熵原理分析CBN砂轮不同磨削性能时声发射信号最大熵概率密度分布，并通过设定交叉熵阈值来辨别磨削加工过程中CBN砂轮的磨削性能。最后，为验证该方法的实用性，在某工厂CBN砂轮磨削产品生产线上进行大量实验研究，结果表明，该方法对CBN砂轮磨损状态及CBN砂轮剩余寿命进行有效监测，验证了该方法监测CBN砂轮在磨削加工过程中磨削性能的有效性。

Abstract

In order to effectively evaluate the grinding performance of CBN（Cubic Boron Nitride） grinding wheel in the grinding process, a monitoring method of CBN grinding wheel performance was proposed based on Shannon entropy theory and acoustic emission signal. Firstly, the acoustic emission signal of CBN grinding wheel was collected by an acoustic emission sensor. Then, the probability density and distribution of acoustic emission signal of CBN grinding wheel was estimated by using the maximum information entropy. In addition, the characteristics of acoustic emission signals of CBN grinding wheel during cyclic grinding after dressing and residual grinding with different diameters were analyzed and discussed. Subsequently, the relationship between the maximum entropy probability density distribution of acoustic emission signals and the different grinding performance of CBN grinding wheel was established according to the cross entropy principle. Finally, a large number of experiments verified the availability above mentioned estimation method. The CBN grinding wheel wear status and the remaining life of CBN grinding wheel can be monitored.

关键词

CBN砂轮磨削性能声发射信号Shannon熵最大信息熵交叉熵

Keywords

Grinding performance of CBN wheelAcoustic emission signalShannon entropyMaximum information entropyCross entropy

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

STOCHASTIC MODEL UPDATING BASED ON THE KRIGING MODEL AND WAVELET PACKET ENERGY SPECTRUM (MT)

A STUDY ON FATIGUE DAMAGE IDENTIFICATION METHOD OF A BLADE COMPOSITE LAMINATE WITH DELAMINATION DEFECTS (MT)

Related Author

No data

Related Institution

School of Mechanical Engineering, Lanzhou Jiaotong University

School of Architecture ＆ Civil Engineering,Shenyang University of Technology

School of Mechanical Engineering,Shenyang University of Technology

School of Mechanical Engineering,Liaoning Institute of Science and Technology

⁰