LONGITUDINAL VIBRATION CHARACTERISTICS OF DRILL BIT IN DRILLING RIG INFLUENCE ON WEAR AND MECHANISM OF TOOTH WHEEL END

XIE Miao; LI ChenGuang; LI Cui; ZHANG HongYu

doi:10.16579/j.issn.1001.9669.2019.02.033

您当前的位置：

首页 >

文章列表页 >

LONGITUDINAL VIBRATION CHARACTERISTICS OF DRILL BIT IN DRILLING RIG INFLUENCE ON WEAR AND MECHANISM OF TOOTH WHEEL END

更新时间：2022-09-22

- LONGITUDINAL VIBRATION CHARACTERISTICS OF DRILL BIT IN DRILLING RIG INFLUENCE ON WEAR AND MECHANISM OF TOOTH WHEEL END
- Journal of Mechanical Strength Vol. 41, Issue 2, Pages: 458-462(2019)
- 作者机构：
  
  1. 辽宁工程技术大学机械工程学院
- 作者简介：
- 基金信息：
- DOI：10.16579/j.issn.1001.9669.2019.02.033
  CLC：
扫描看全文
XIE Miao, LI ChenGuang, LI Cui, et al. LONGITUDINAL VIBRATION CHARACTERISTICS OF DRILL BIT IN DRILLING RIG INFLUENCE ON WEAR AND MECHANISM OF TOOTH WHEEL END. [J]. 41(2):458-462(2019)
DOI：

XIE Miao, LI ChenGuang, LI Cui, et al. LONGITUDINAL VIBRATION CHARACTERISTICS OF DRILL BIT IN DRILLING RIG INFLUENCE ON WEAR AND MECHANISM OF TOOTH WHEEL END. [J]. 41(2):458-462(2019) DOI： 10.16579/j.issn.1001.9669.2019.02.033.

摘要

牙轮钻头轴端的磨损是多方面因素造成的,主要从牙轮钻机钻井时钻头纵向振动特性对牙轮轴端的影响进行牙轮轴端磨损机理分析,首先建立三牙轮钻头纵向动力学模型,并在此基础上对三牙轮钻头进行振动特性分析,探究牙轮纵向振动对牙轮轴端磨损的影响,建立牙轮微动磨损数值计算模型,得出牙轮轴端的磨损体积主要受牙轮轴和轴承的接触面的法向压力和牙轮轴和轴承之间的切向相对滑移距离影响。最后对三牙轮钻头的磨损机理进行分析,对牙轮钻头寿命的提高的研究有积极的推动作用。

Abstract

The abrasion of the shaft end of the cone bit is caused by many factors, In this paper, we mainly analyze the effect of the longitudinal vibration characteristic of the drill bit on the end of the tooth wheel on the wear and mechanism of the tooth axle end. And firstly, the longitudinal dynamic model of the three-cone bit is established, and on this basis, the vibration characteristics of the three-cone bit are analyzed, and the influence of the longitudinal vibration of the roller on the wear of the tooth wheel is explored, and the numerical model of fretting wear is established. It is found that the wear volume of the tooth axle end is mainly affected by the normal pressure of the contact surface of the tooth axle and the bearing and the tangential relative slip distance between the tooth axle and the bearing. At last, the paper analyzes the wear mechanism of the three-cone bit and has a positive effect on the study of the improvement of the life of the cone bit.

关键词

牙轮钻头磨损机理纵向振动微动磨损数值计算

Keywords

Roller bitWear mechanismLongitudinal vibrationFretting WearNumerical calculation

references

Views

254

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

STUDY ON WEAR MECHANISM OF CUTTING CAST IRON BY NITROGEN SILICON COATING CERAMIC TOOL

EXPERIMENTAL STUDY ON LATERAL FRETTING WEAR OF FLANGE BOLTS

ANALYSIS OF THE EFFECT OF LIQUID VISCOSITY ON ROLLING CONTACT FATIGUE CRACK PROPAGATION OF RAIL

RESEARCH ON NUMERICAL ANALYSIS OF ELECTROMAGNETIC FIELD BASED ON A NEW ACTIVE NUMERICAL ALGORITHM

SIMULATION FOR THE PRESSURE LOSS OF AUTOMOTIVE EXHAUST MUFFLER

Related Author

No data

Related Institution

College of Mechanical and Automotive Engineering,Zhaoqing College

Shenyang University of Technology Academy of Mechanical Engineering

Tribology Research Institute,State Key Laboratory of Traction Power,Southwest Jiaotong University

State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body,Hunan University

School of Information,Ningbo City College of Vocational Technology

⁰