RESEARCH ON THE CRACKING MECHANISM OF THE MAIN GIRDER OF 350T CASTING CRANE

WANG XiaoXi; LUO HuiXin; DANG Zhang; XU WeiWen; ZHANG QinFen

doi:10.16579/j.issn.1001.9669.2017.05.040

您当前的位置：

首页 >

文章列表页 >

RESEARCH ON THE CRACKING MECHANISM OF THE MAIN GIRDER OF 350T CASTING CRANE

更新时间：2022-09-22

- RESEARCH ON THE CRACKING MECHANISM OF THE MAIN GIRDER OF 350T CASTING CRANE
- Journal of Mechanical Strength Vol. 39, Issue 5, Pages: 1230-1233(2017)
- 作者机构：
  
  1. 武汉科技大学机械学院
  2. 武汉钢铁股份有限公司设备管理部
- 作者简介：
- 基金信息：
- DOI：10.16579/j.issn.1001.9669.2017.05.040
  CLC：
扫描看全文
WANG XiaoXi, LUO HuiXin, DANG Zhang, et al. RESEARCH ON THE CRACKING MECHANISM OF THE MAIN GIRDER OF 350T CASTING CRANE. [J]. 39(5):1230-1233(2017)
DOI：

WANG XiaoXi, LUO HuiXin, DANG Zhang, et al. RESEARCH ON THE CRACKING MECHANISM OF THE MAIN GIRDER OF 350T CASTING CRANE. [J]. 39(5):1230-1233(2017) DOI： 10.16579/j.issn.1001.9669.2017.05.040.

摘要

以某炼钢厂连铸车间炉前350 t铸造起重机为研究对象,针对吊车主梁端部出现裂纹的问题,结合现场压力测试及有限元仿真对问题进行分析并提出加固方案。通过应力实测对有限元计算结果进行验证,验证有限元模型正确后对主梁端部最危险的工况进行静应力分析,有限元计算结果表明,最大应力出现在主梁端部。结合实际观察情况,以有限元计算结果为依据,认为主梁端部弯板弧度较小、端梁下盖板与主梁端部弯板对接焊缝在该处交叉,使得该处应力集中较大,从而导致起重机主梁端部产生裂纹。最后结合实际问题提出加固方案,并通过有限元计算结果可知加固效果十分显著。

Abstract

The problem of crack in the end of the crane girder is analyzed by using the 350 t casting crane in a steel plant.The finite element model is verified by the results of stress measurement. The finite element model is correct and the most dangerous condition of the main beam is analyzed. The results show that the maximum stress appears at the end of the main beam. According to the actual observation,the results of the finite element calculation,that the end of the main beam of the lower end of the curved plate,the end of the beam and the main beam end bending plate butt weld in the intersection,the stress concentration of the site,resulting in a crack in the main girder of crane. Finally,the reinforcement scheme is put forward,and the results show that the reinforcement effect is very significant.

关键词

铸造起重机主梁端部裂纹有限元加固

Keywords

Casting craneMain girder endCrackFinite elementReinforcement

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

UN R127 PEDESTRIAN PROTECTION ANALYSIS AND OPTIMIZATION OF THE VEHICLE

EVALUATION FOR REMAINING LIFE OF BRIDGE CRANE BASED ON RADIAL BASIS NEURAL NETWORK

RESEARCH ON PROPAGATION CHARACTERISTICS OF FATIGUE CRACK AND LIFE PREDICTION FOR THE PANTOGRAPH

SIMULATION ANALYSIS AND GROUND TEST OF SOLID ROCKET MOTOR GRAIN WITH SURFACE CRACK

MILLING OF WEAK RIGID PARTS BASED ON MRF FLEXIBLE AUXILIARY SUPPORT

Related Author

No data

Related Institution

Faw Haima Automobile Co.,Ltd.

Department of Industry and Information Engineering,Vocational Technology College of Hainan

School of Mechanical Engineering, Taiyuan University of Science and Technology

State Key Laboratory of Traction Power,Southwest Jiaotong University

Technology Center,CRRC Qingdao Sifang Co.,Ltd.

⁰